ESWLogo
MGlogoblue

Pellet (and Corn / Multi-fuel) Vent Pipe

Elbows...Tees...Through-the-Wall Kits...etc...etc...


MG Dura-Vent is an industry leader in venting systems for pellet (and multi-fuel/corn) stoves. Their system "features a double-wall, air-insulated design to ensure superior performance and safety."
Dura-Vent's pipe provides minimum clearance (usually 3") to combustibles, and it has special features such as gaskets and seals to prevent fly ash leakage.
Now, safe and easy assembly is made more possible than ever with Dura-Vent's precision twist-lock connections.
The pipe is listed by Underwriters Laboratories, and is tested and listed to UL 641 Standard.


If you have any questions pertaining to Dura-Vent's pipe or installation applications of their pipe, contact Dura-Vent at (800) 835-4429.


NOTE: All pellet vent pipe that we sell is 3" diameter (to match our pellet stoves' exhaust outlets), unless otherwise noted. Be sure to follow the pipe manufacturer's instructions when using their pipe. Use Dura-Vent pipe only with other Dura-Vent pipe products (contact them with questions). Be sure to read and follow all installation instructions from the pipe manufacturer and from your England's Stove Works owner's manual before installing one of our units. Be sure to adhere to local codes, and consult a professional installer if necessary.

If you have any further questions, contact Technical Support at (800) 245-6489.


Like many internet documents, some of our information pages are in Adobe PDF format (easy to view and print!).
If you don't have Adobe Acrobat Reader on your system, download a free copy here:

adobe

   
AC-3000PelletVentKit.jpg AC-3000 3" Pellet Vent Kit (16 lbs. each)
$253.41
Through-the-wall 3" Pellet Vent Kit (mfg. by Dura-Vent). Contains all the parts needed for most pellet installations. NOTE: See AC-3000 page on our site for more info. Not for pellet insert. See your manual (and call Technical Support at (800) 245-6489, if questions) for insert installation.
Not for high altitude (over 4,000 ft.); see AC-3100 kit.
See Owner's Manual for information on long runs of pipe, basement installs, and general installation information. Always follow local codes.
[Add to Cart]  [View Cart]

   
PU-3067.jpg AC-3067 Tee (3 lbs. each)
$73.73
Tee with Cleanout Adapter. 3" diameter pellet pipe. Convenient twist-lock connection. Creates 90 degree offset with clean-out access; easy access for cleanout of ash, including fly ash.

[Add to Cart]  [View Cart]

   
PU-OAK.jpg PU-OAK Outside Air Kit for Pellet Units (3 lbs. each)
$60.58
This kit is manufactured by England's Stove Works. Provides outside fresh air that is mandatory for most pellet and multi-fuel installations (including all England's Stove Works models).
Complete, through-the-wall outside air installation kit for pellet and multi-fuel units includes: Aluminum Flex Hose (expands to 6'); Aluminum Screen; Inside Wall Plate; Outside Wall Plate; Weather Hood; Hose Clamps.
For 10-CDV, 25-PDVC, 49-SHC22, 55-SHP10, 55-SHP10L, 49-TRC22, 55-TRP10 and American Standard 1998 and newer.
For 25-PDV, 55-SHP22, 55-SHP22L, 55-TRP22 and American Heritage 2001 and newer.
Also for multi-fuel stoves (stoves with CPM in model number); for "Evolution Pellet" stoves (stoves with EP in model number); for Pellet Auxiliary Heaters (stoves with PAH in model number); and for "Imperial Pellet" stoves (stoves with IP in model number).
Will not work with old pellet add-on furnace models (25-PAF).
For more information on the PU-OAK Outside Air Kit, Click Here
[Add to Cart]  [View Cart]

   
AC-3045.jpg AC-3045 45 Degree Elbow (2 lbs. each)
$44.08
For 3" pellet vent pipe. 45 degree elbow is ideal for corner installations (to connect cater-cornered stove to a through-the-wall kit). Can offset pipe diagonally or horizontally. Convenient twist-lock connection; elbow is not adjustable. Factory silicone sealed to contain fly ash.
[Add to Cart]  [View Cart]

   
AC-3090.jpg AC-3090 90 Degree Elbow (2 lbs. each)
$55.07
For 3" pellet vent pipe. 90 degree elbow is ideal for when you need an extra elbow in your installation. Can offset pipe diagonally or horizontally. Convenient twist-lock connection; elbow is not adjustable. Factory silicone sealed to contain fly ash. NOTE: Use 45-degree elbows (AC-3045) whenever possible, as 90-degree elbows reduce draft more than 45-degree elbows. Consult your Owner's Manual and call Technical Support with questions.
[Add to Cart]  [View Cart]

   
AC-3012.jpg AC-3012 1' Section Pellet Pipe (2 lbs. each)
$25.33
One-foot (1') long section of 3" pellet vent pipe; uses the "twist lock" connection. Gives 3" clearance to combustibles, and can be used in horizontal or vertical installations.
NOTE: Although pipe shown is black, this part is Galvalume for exterior installation (see AC-3067 for example of Galvalume finish).
[Add to Cart]  [View Cart]

   
PU-3079.jpg PU-3079 Pipe Adapter (2 lbs. each)
$13.53
3" Pellet Pipe Adapter. Adapts into appliance outlet, allowing pipe to easily connect or disconnect. Can be used for horizontal or vertical installations.
Good for use with our pellet insert model, but can be used on any of our pellet units.
[Add to Cart]  [View Cart]

   
AC-3000PelletVentKit.jpg AC-3100 4" Pellet Vent Kit (19 lbs. each)
$313.72
Through-the-wall 4" Pellet Vent Kit for high-altitude installations (over 4,000 ft.). Contains all the parts needed for most (high-altitude) pellet installations. Comes with 3" - 4" increaser, so it will work with our stoves (or others) with 3" diameter exhaust. Mfg. by Dura-Vent.
NOTE: See AC-3000 page on our site for more info. Although this info. page will be for the AC-3000 kit, this kit is similar (except that this kit is 4" diameter pipe instead of 3").
Not for pellet insert. See your manual (and call Technical Support at (800) 245-6489, if questions) for insert installation.
See Owner's Manual for information on long runs of pipe, basement installs, and general installation information. Always follow local codes.
[Add to Cart]  [View Cart]

   
AC-33000.JPG AC-33000 3" Corn / Multi-fuel Vent Kit (Through-the-Wall) (16 lbs. each)
$295.00
Dura-Vent 3" Corn Vent Kit (Through-the-Wall). Made especially for corn-burning stoves, which includes our corn and multi-fuel (agri-fuel) models.
Includes: Horizontal Cap, 90 Degree Elbow, Tee Support Bracket, (5) Pieces of 12" Strait Length Pipe, Tee w/Clean-out Cap, Wall Thimble, and Adapter.
NOTE: If installing over 2,500 ft. altitude, use 4" diameter pipe instead. See Owner's Manual for information on long runs of pipe, basement installs, and general installation information. Always follow local codes.
[Add to Cart]  [View Cart]

   
AC-3074.jpg AC-3074 Dura-Vent 3" to 6" increaser (3 lbs. each)
$63.06
AC-3074 Dura-Vent 3" to 6" increaser is for connecting to premanufactured pipe chimney only, not for connecting to masonry chimney.
Per Dura-Vent, use with a close clearance connector to fasten into support box or wall thimble. Contact Dura-Vent with any questions concerning this at (800) 835-4429.

[Add to Cart]  [View Cart]

   
AC-3036.jpg AC-3036 3' Section Pellet Pipe (4 lbs. each)
$44.66
Three-foot (3') long section of 3" pellet vent pipe; uses the "twist lock" connection. Gives 3" clearance to combustibles, and can be used in horizontal or vertical installations.
NOTE: Although pipe shown is black, this part is Galvalume for exterior installation (see AC-3067 for example of Galvalume finish).
[Add to Cart]  [View Cart]

   
AC-3012A.jpg AC-3012A 1' Section Adjustable Length Pellet Pipe (2 lbs. each)
$33.57
One-foot (1') long section of 3" pellet vent pipe.
How it works: Use when a fixed length of pellet vent pipe is not appropriate. This pipe must be used in conjunction with another piece of rigid (non-adjustable) twist-lock pipe. It slides along the other piece of pipe, so that it will add anywhere from 3" to 10" to the other piece of pipe.
For example, if used in conjunction with another 12" section of pipe, the two pieces together could adjust from 15" to 22" in total length.
[Add to Cart]  [View Cart]

   
AC-3043.jpg AC-3043 Wall Thimble (4 lbs. each)
$48.45
This wall thimble is made for 3" Pellet Vent Pipe by Dura-Vent. It fits between standard wall studs. Interior trim painted black.
[Add to Cart]  [View Cart]


Order Inquiries? Email orders@englanderstoves.com or call (Parts Orders & Inquiries ONLY) - (800) 516-3636.

For Customer Service or Technical Questions - Email service@englanderstoves.com or call (800) 245-6489.

We appreciate your business!
*We are not vulnerable to the 'Heartbleed' bug, we are secure.

Your Order
is Secure!
2014 England's Stove Works, Inc.
England's Stove Works, Inc. Home Page