Through-the-Wall Installation

England's Stove Works recommends professional installation of our hearth products.


England's Stove Works strongly recommends installation of smoke and carbon monoxide detectors when installing ANY  type of stove.

The through-the-wall installation is the least expensive and simplest installation. In a through-the-wall installation you should be mindful of the snowdrift line, as well as dead grass and leaves. We recommend a three foot (3') minimum vertical rise on the inside or the outside of the dwelling. Never terminate the end vent under a deck, in an alcove, under a window or between two windows. Call (800) 516-3636 to inquire about the AC-3000 Through-the-Wall Kit.


Click here for AC-3000 kit

Click here for AC-3100 kit
(altitude above 4,000 ft)


To vent the unit through the wall, connect the pipe adapter to the exhaust motor adapter. If the exhaust adapter is at least eighteen inches (18") above ground level, a straight section of pellet pipe can be used to initially pass through the wall (see Ill. 1 in manual). Your dealer or our factory should be able to provide you with a kit that will handle most of this installation, which will include a wall thimble that will allow the proper clearances through a combustible wall. Once outside the structure, a three-inch (3") clearance should be maintained to the outside wall and a clean out tee should be placed on the pipe that extends through the wall. We recommend a minimum of three feet (3') of vertical pipe with a 90-degree turn away from the house. At this point, a one-foot (1') section and horizontal cap will complete the installation (see Illustration 1 in manual). A wall strap should be placed just below the last 90-degree section to make the system more stable. If you live in an area that has heavy snowfall, it is recommended the installation be taller than three feet (3') to get above the snowdrift line.

        Through the wall

Vent kit(AC-3000)


(use AC-3100
if above 4,000 ft)


Outside Air Kit (PU-OAK)

Outside Air (Outside Combustion Air Intake)

Outside air is mandatory for this unit to operate properly. This unit has been designed and tested with this connection, because so many homes are airtight and there is not adequate combustion air available inside the dwelling. The air intake pipe is located on the bottom side of the burn pot (from the rear) and measures 11/2" inside diameter (I.D.). The connection can be made with a metal 17/8" I.D. coupler and pipe, and should exit through the wall. Be sure to secure the pipe to the unit with a clamp or aluminum tape. The outside end of the pipe should be covered (screened) to prevent foreign matter from entering the system. Our Outside Air Kit (Part Number PU-OAK) can be used. If the unit is located below ground level, you will need to run the pipe up and then outside the dwelling. NOTE: If the total run of the connection exceeds 6', if more than 2 elbows are used, or if a basement installation, use 3" metal pipe (and coupler) instead.

Click here for Basement Installation Instructions


If an older unit, measure the opening to determine what size pipe to use or couple to.

 Click here for Outside Air Kit (Part # PU-OAK)



High Altitude Installation

If the unit is being installed at an altitude of 4,000 ft. above sea level or higher, the following amendments to the chosen installation should be made:

  1. The pellet vent pipe size should be increased to 4" (Part # AC-3100 vent kit) if choosing a "through-the-wall" installation. If connecting to an existing chimney use 4" pellet vent pipe.

  2. The outside air intake should be increased to 3".

If you have any further questions or concerns, please contact Customer Service at:

Copyright © 2005   England's Stove Works, Inc.   All rights reserved.
Revised:  11/07/2008

This web site, including all pictures, description and information of any sort contained therein is intended for the sole use of customers and representatives of England's Stove Works, Inc. No part of this web site or the information contained therein may be reproduced without express written permission from England's Stove Works, Inc..